G3 Quiz 27

Time limit: 0

Quiz Summary

0 of 10 Questions completed

Questions:

Information

You have already completed the quiz before. Hence you can not start it again.

Quiz is loading…

You must sign in or sign up to start the quiz.

You must first complete the following:

Results

Quiz complete. Results are being recorded.

Results

0 of 10 Questions answered correctly

Your time:

Time has elapsed

You have reached 0 of 0 point(s), (0)

Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)

Categories

Not categorized 0%

1
2
3
4
5
6
7
8
9
10

Current
Review
Answered
Correct
Incorrect

Question 1 of 10

1. Question
114)Gas piping regulations are in section ___________ of the B149.2 propane code.
- A. 2
- B. 3
- C. 6
- D. 8
Correct

Incorrect
Question 2 of 10

2. Question
115)Equipment service bulletins are normally issued by the:
- A. local utility or fuel supplier.
- B. manufacturer.
- C. Canadian Gas Association.
- D. Canadian Standards Association
Correct

Incorrect
Question 3 of 10

3. Question
116)Safety directives and bulletins are published by:
- A. the local utility or fuel supplier.
- B. the manufacturer.
- C. TSSA
- D. the Underwriters' Laboratories of Canada
Correct

Incorrect
Question 4 of 10

4. Question
117)Which information is in both the Natural Gas and Propane code books?
- A. responsibility of the installer, individual installation data for each type of appliance, clearances from combustibles, piping practices, pipe sizing charts, venting tables
- B. individual appliance installation instructions, clearances form other equipment, fan size, venting tables, piping types, responsibility of fuel supplier
- C. what an installer can do, who can weld 2 inch pipe, who can install underground piping, who can install more than one appliance, clearances from combustibles
- D. pipe sizing, regulator sizing, vent sizing, water pipe sizing, responsibility of the installer, piping practices, clearances form combustibles
Correct

Incorrect
Question 5 of 10

5. Question
118)The word “symptom” is used manufacturers literature to describe:
- A. how a piece of equipment functions.
- B. problems arising because of equipment venting.
- C. problems arising because of equipment wiring.
- D. abnormal operation of the equipment
Correct

Incorrect
Question 6 of 10

6. Question
119)To correct a symptom such as a fluctuating flame:
- A. notify the local utility or fuel supplier.
- B. contact the equipment supplier.
- C. consult the manufacturer's checklist.
- D. exchange the appliance and contact the manufacturer
Correct

Incorrect
Question 7 of 10

7. Question
120)The manufacturer’s installation instructions and equipment packing list normally advise an installer to have which of the following items to complete an installation?
- A. hand tools, gas pressure test gauge, leak detector, stop watch, pipe threader, electrical wire, thermostat wire, torch, solder, grease for joining pipe threads, heavy gauge venting material, and sheet metal screws
- B. gas pressure test gauge, leak detector, sheet metal screws, gas pipe, wiring, stop watch, manometer, voltmeter, appropriate gauge vent material, CSA approved pipe joining compound, hand tools, and pop rivets
- C. hand tools, extension cord, drill, pipe wrenches, pipe threader, approved pipe joining compound, sheet metal screws, a list of required pipe and fittings, a list of required wiring materials, a list of required venting materials
- D. hand tools, drill, pipe wrenches, wiring materials, duct tape for venting joints, approved pipe joining compound, voltmeter, extension cord, manometer, stop watch, multimeter, gas pressure gauge
Correct

Incorrect
Question 8 of 10

8. Question
121)Equipment specifications indicate mainly:
- A. dimensions required to install the appliance, weight of the equipment, electrical characteristics, size and location of the vent outlet, piping inlet size, model number
- B. size of building required to accommodate the equipment, parts list, weight of equipment, installation clearances, piping outlet size, serial number
- C. address of installation, required appliance output, electrical characteristics, weight of equipment, branch piping size, model number
- D. physical dimensions required to install the appliance, weight of the equipment, amount of fuel consumed, CO content of the fuel consumed, electrical characteristics, size and location of the vent outlet
Correct

Incorrect
Question 9 of 10

9. Question
122)Drawings that show multiple views of an object for clarification are called:
- A. pictorial drawings.
- B. orthographic drawings.
- C. schematic drawings.
- D. rotational drawings
Correct

Incorrect
Question 10 of 10

10. Question
123)As the temperature of liquid propane in a tank increases, the vapour pressure of the propane:
- A. increases.
- B. decreases.
- C. remains the same.
- D. fluctuates.
Correct

Incorrect

G3 Quiz 27

Quiz Summary

Information

Results

Results

Categories

1. Question

2. Question

3. Question

4. Question

5. Question

6. Question

7. Question

8. Question

9. Question

10. Question