G3 Quiz 26

Time limit: 0

Quiz Summary

0 of 10 Questions completed

Questions:

Information

You have already completed the quiz before. Hence you can not start it again.

Quiz is loading…

You must sign in or sign up to start the quiz.

You must first complete the following:

Results

Quiz complete. Results are being recorded.

Results

0 of 10 Questions answered correctly

Your time:

Time has elapsed

You have reached 0 of 0 point(s), (0)

Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)

Categories

Not categorized 0%

1
2
3
4
5
6
7
8
9
10

Current
Review
Answered
Correct
Incorrect

Question 1 of 10

1. Question
104)Welded gas piping must comply with the:
- A. National Building Code
- B. Occupational Health and Safety Act and Regulations
- C. Technical Standards and Safety Act
- D. Dangerous Goods Transportation Act and Regulations
Correct

Incorrect
Question 2 of 10

2. Question
105)When manufacturer’s instructions do not state the required clearances between combustible materials and the base of a factory built chimney, the installer may refer to the:
- A. Ontario Building Code
- B. Occupational Health and Safety Act and Regulations
- C. Technical Standards and Safety Act
- D. Dangerous Goods Transportation Act and Regulations
Correct

Incorrect
Question 3 of 10

3. Question
106)A G.2 Technician:
- A. may replace a defective residential automatic gas-fired water heater
- B. must advise the user of the appliance that a plumber is required to replace the defective automatic water heater
- C. may recharge an add-on central air conditioner with refrigerant
- D. may design and install the duct work required for a new installation
Correct

Incorrect
Question 4 of 10

4. Question
107)When a new appliance is to be installed where the municipality requires work permits and inspections for every installation:
- A. the installer may proceed with the installation and apply for the installation permit and the inspection once the work has started
- B. it is the responsibility of the homeowner to secure the necessary permits and the inspections
- C. it Is the responsibility of the installer to secure the necessary permits and the inspections
- D. it is the responsibility of the municipality to inform the installer that an installation permit and an inspection are required
Correct

Incorrect
Question 5 of 10

5. Question
108)The installation of gas-burning appliances in mobile homes shall be in accordance with:
- A. CSA Standard Z240.4.1
- B. CSA Standard Z240.4.2
- C. CSA Standard B139
- D. CGA Standard B149.2
Correct

Incorrect
Question 6 of 10

6. Question
109)The installation of gas-burning appliances in mobile homes shall be in accordance with:
- A. CSA Standard Z240.4.1
- B. CSA Standard Z240.4.2
- C. CSA Standard B139
- D. CGA Standard B149.2
Correct

Incorrect
Question 7 of 10

7. Question
110)What is the largest size of propane cylinder manufactured:
- A. 240 lbs. WC (109 kg)
- B. 300 lbs. WC (136 kg)
- C. 420 lbs. WC (190 kg)
- D. 1,000 lbs. WC (454 kg)
Correct

Incorrect
Question 8 of 10

8. Question
111)When cylinders are being transported, they shall be secured:
- A. vertically with chains and straps and a relief valve, in a well ventilated space
- B. in an upright position with chains and straps and a relief valve, in a well-ventilated space
- C. in an upright position, in a well-ventilated location with the relief valve communicating with the vapour space only
- D. in an upright position, in a well-ventilated location with the relief valve communicating with the liquid space only
Correct

Incorrect
Question 9 of 10

9. Question
112)The Ontario Natural Gas Utilization Code is used to determine:
- A. the best method to clean gas appliances.
- B. the input of gas appliances.
- C. regulations for installing gas appliances.
- D. the gas pressure for gas entering a house
Correct

Incorrect
Question 10 of 10

10. Question
113)All furnace appliance manufacturers’ literature gives the name of the manufacturer, the:
- A. physical dimensions, fan motor electrical resistance data, and the Btuh input.
- B. Btuh input, fan size, CFM, voltage, fuse size, and the physical dimensions.
- C. fuse size, Btuh output, amount of heat required to heat the building, and the size of wire.
- D. size of chimney or vent riser, Btuh output, fuse size, and the physical dimensions
Correct

Incorrect

G3 Quiz 26

Quiz Summary

Information

Results

Results

Categories

1. Question

2. Question

3. Question

4. Question

5. Question

6. Question

7. Question

8. Question

9. Question

10. Question